AplTVY3-B3-1sk-4T

HW: Arduino realizace: Maxa David Charvát Jakub Lukáš Jílek

Robot Arduino

Úkoly:

• Sestavte robota, napište program a vyzkoušejte proto, aby robot:

se pohyboval vpřed do vzdálenosti 1m

int motor_left[] = {6, 7}
int motor_right[] = {8, 10}

void setup() {
Serial.begin(9600);
int i;
for(i = 0; i < 2; i++){
pinMode(motor_left[i], OUTPUT);
pinMode(motor_right[i], OUTPUT);

drive_forward();
delay(6200);
motor_stop();
Serial.println("1");

}
}

void loop() {

}
 
void motor_stop(){
digitalWrite(motor_left[0], LOW);
digitalWrite(motor_left[1], LOW);
 
digitalWrite(motor_right[0], LOW);
digitalWrite(motor_right[1], LOW);
}
 
void drive_forward(){
digitalWrite(motor_left[0], HIGH);
digitalWrite(motor_left[1], LOW);
 
digitalWrite(motor_right[0], HIGH);
digitalWrite(motor_right[1], LOW);
}

se pohyboval vpřed ve čtyřúhelníku o straně cca 0,5m

int motor_left[] = {6, 7};

int motor_right[] = {8, 10};
void setup() {
Serial.begin(9600);
int i;
for(i = 0; i < 2; i++){
pinMode(motor_left[i], OUTPUT);
pinMode(motor_right[i], OUTPUT);
}
}

void loop() {}
 
drive_forward();
delay(3200);
motor_stop();
Serial.println("1");
 
turn_left();
delay(420);
motor_stop();
Serial.println("3");
 
motor_stop();
delay(1000);
motor_stop();
Serial.println("5");

}
 
 
void motor_stop(){
digitalWrite(motor_left[0], LOW);
digitalWrite(motor_left[1], LOW);
 
digitalWrite(motor_right[0], LOW);
digitalWrite(motor_right[1], LOW);
delay(25);
}
 
void drive_forward(){
digitalWrite(motor_left[0], HIGH);
digitalWrite(motor_left[1], LOW);
 
digitalWrite(motor_right[0], HIGH);
digitalWrite(motor_right[1], LOW);
}
 
void turn_left(){
digitalWrite(motor_left[0], LOW);
digitalWrite(motor_left[1], HIGH); 
digitalWrite(motor_right[0], HIGH);
digitalWrite(motor_right[1], LOW);
}

se pohyboval dokud nebude stisknutý dotykový senzor

int analogPin = 1; // potentiometer wiper (middle terminal) connected to analog pin 3

                      // outside leads to ground and +5V

int val = 0; // variable to store the value read

int motor_left[] = {6, 7};

int motor_right[] = {8, 10};

void setup() {

 Serial.begin(9600);          //  setup serial
  int i;
for(i = 0; i < 2; i++){
pinMode(motor_left[i], OUTPUT);
pinMode(motor_right[i], OUTPUT);

} }

void loop() {

 val = analogRead(analogPin);    // read the input pin
 Serial.println(val);             // debug value

if (val>600)

 {
 drive_forward();
 delay(1000);
 }
 if (val <600)
{
motor_stop();

} }

void motor_stop(){

digitalWrite(motor_left[0], LOW);
digitalWrite(motor_left[1], LOW);

digitalWrite(motor_right[0], LOW);

digitalWrite(motor_right[1], LOW);
delay(25);
}

void drive_forward(){

digitalWrite(motor_left[0], HIGH);
digitalWrite(motor_left[1], LOW);

digitalWrite(motor_right[0], HIGH);

digitalWrite(motor_right[1], LOW);
}

void drive_backward(){
digitalWrite(motor_left[0], LOW);
digitalWrite(motor_left[1], HIGH);

digitalWrite(motor_right[0], LOW);

digitalWrite(motor_right[1], HIGH);
}